Create or find the look you’re after. This will determine the type and size of board you need for creating the sign. If you want to create an authentic aged look, start with recycled or aged wood. Even better if it has old paint still on it. If starting with fresh unpainted wood, paint the background color first. At this stage, you may also want to add a little molding or trim around the perimeter of the sign to dress it up a little. Once the background color is applied, then start with the lettering and or images for your sign. If you’re copying something you’ve found in a magazine or online, you might be able to use a simple table projector to superimpose the image onto your sign. Then trace the design with a pencil onto your sign and paint as desired. If you’re painting freehand, be careful to not choose a design too intricate as you’re edges will not be terribly crisp. Small designs can be copied using a Sharpie or other marker, which allow for greater control. Many older signs were hand painted which adds to the rustic charm and with practice you may be able to achieve this look yourself. My ‘laundry’ sign was done by projecting an image I found online (I printed it up first), tracing it in pencil and then using a blue sharpie to color it in. My ‘cigar’ sign was also projected onto the wooden sign I made first, but in this case I just carefully painted the lettering using a small artists brush. If you choose a very detailed design and want it too look very professional, you may opt to have a mask made at a professional sign/banner store. Take your image and sign measurements to the store and they will use their computer to cut out the image in a sticky vinyl sheet, which you lay over top of your sign. When you peel off the top layer of the vinyl, the mask acts like a stencil where you simply paint over the relief of your lettering. When the cut out areas have been fully covered in the color of your choice, you just peel off the mask and your painted lettering will remain on your sign, looking very precise. I used this process with the my larger signs (Southwell & Company, and Oakville Yacht Club). Once all the lettering and design work has been painted on, you may want to distress the piece afterward to make it look really old. You could literally add dents and small cuts to the wood using a variety of tools – one of the tricks of the trade is to tie a large number of metal keys on a wire ring and attach the ring to a wooden handle and then hit the wood with the keys. The keys will create small random gouges and depressions along the woods surface without doing too much damage. Another way to age the piece is to sand off areas of the sign to give the impression of the colors fading over time. This takes a little skill but if you look at real vintage signs, you’ll get an idea how best to sand your piece. After sanding, I often add stain or glaze to the piece to add another layer of age. If you’ve sanded any edges down to raw wood, then you’ll want to age those areas so they don’t look like new wood. Light brown stain, which you quickly wipe off or a glaze tinted with umber can also create a great aged look. Apply sparingly over the whole piece and add layers as needed. Remember to never apply polyurethane (oil based) finish coats over your painted projects. Polyurethane eats away at paint and will destroy your finish. If you feel you must apply a protective finish over your finished project, you must use a polyacrylic (water based) finish. Keep in mind, any shiny finish coat will detract from a vintage look where truly old wooden signs have a matte, very worn feeling from many years of exposure to the elements.
1 cup Shea Butter1 cup Coconut oil1 cup Beeswax4 tablespoons Zinc oxide powder (Sophie recommends non nano)1 teaspoon essential oil: sandalwood Heat a double boiler - I place a glass bowl over a pot of boiling water. Place the butter, oil and pellets in the bowl and heat until completely melted (3-4 minutes). Remove from heat, and whisk in zinc oxide and 1tsp of essential oil - pour into molds. Lotion bars will set in a couple of hours (1 hour in the fridge). But you can keep in the molds for as long as you want, and best to do this if you aren't going to use right away.
24" Wood round or wine barrel topPaint, stencils, paint brushLazy susan metal hardwareScrewsDrillPiece of feltScissorsBlock of wood Get a 24’’ round piece of wood. You can also use a wine barrel top. Attach and center your lazy susan metal hardware – These come in varied shapes, I recommend using the square pieces. Attach your block of wood, using your drill (separating each by a piece of felt). Finally, using paint, stencil and a paint brush, customize your lazy susan! You can also add embellishments, lace, glitter, and of course, some mod podge!
Steps: Use a highlighter that's 2-3 shades lighter than your foundation. Find your cheekbones- make a fish face or use your fingers to press gently into the hallow area under your cheek bone. Use a Bronzer or foundation. (Cream is best) that's at least 2 - 3 shades darker than your foundation - and sweep it in the hallows you just found. Minimize any other areas that apply to you using the same contour shade- forehead apply at hairline to lower high forehead - at temples to minimize a wide forehead. Contour the crease of the eyes , according to eye shape... Deep set, hooded, prominent etc…. Keeping it simple - use the same contour to shape the sides of the nose - adjusting highlighter and contour to fix a too wide / too narrow nose - or just to keep it in harmony with the rest of the make up. Brush contour under jawline to help accentuate it's shape and to reduce any gravity nonsense... Double chin if you will. Using your regular foundation color --- stipple it over the highlight and contour and blend it in using a stipple brush…. Set with translucent powder. Finish makeup - eyes, blush lips. Use a contour brush or blush brush to apply contour.
200 ft. 3/8" sisal rope, color of your choosingOne 6’ 4x4 untreated plywood postFour 14" utility shelf bracketsFour 5" utility shelf bracketsFour 18" untreated plywood roundsOne 3’ diameter untreated plywood roundsUntreated carpet, color of your choosing, sized the width of your boards2 yards of 3" thick Industrial/heavy duty VelcroMedium-sized cup hooksWood glueDrillWood screwsStaple gun⅜" staple gun staples
